How To Put A Wheel On A Skateboard

Irresolute Skateboard Wheels

Changing skateboard or longboard wheels is a simple task that can drastically change the way your lath rides. Wheels eventually wear out after a while and information technology's important to know when wheels tin can exist fixed with DIY tricks or when information technology's time for a fresh four.

When to Change Your Wheels

Skateboard wheels can last you a long time, simply if y'all are skating every twenty-four hours or doing a lot of powerslides they will wear down faster. A few good indicators that information technology'south fourth dimension for a new set up of wheels is if they are coned, become very small or get gnarly flat spots. All of these issues will cause your lath to feel tedious and make for a rougher ride. These problems are frustrating, just tin be cured by swapping out your busted wheels for some new ones.

We'll teach yous how to change your skateboard wheels in 4 easy steps. Follow along or spring to one of the steps below:

Remove Wheels
Remove Bearings
Insert Bearings into New Wheels
Mount Wheels

Tips:

Softer wheels will be easier to alter out than harder wheels because removing and inserting bearings requires less endeavor. Longboards and cruisers use softer wheels, while harder wheels are ideal for regular skateboards. No matter the board style, the process for irresolute wheels remains the same.
If you demand some aid choosing wheels, cheque out our cycle buying guide.

Gather Materials

Before you start, you'll demand a few tools and materials. Once you have everything together, we'll teach you how to change your skateboard wheels in 4 easy steps.

Skate tool (or wrench)
Tray (to store hardware)
Skateboard Trucks

Store Skate Tools

Stride i. Remove Wheels

Begin past removing the beam basics with your skate tool or wrench and sliding the wheels off of your truck beam. Make sure to keep rails of the washers that sit down on either side of the wheel. We observe information technology all-time to organize and store the beam nuts and speed washers in a small tray so you don't lose any small pieces of hardware.

Step 2. Remove Bearings

Next, you'll remove your bearings from your wheels by prying them out of your wheels using the axle of your truck. To do this, slide the bike half-fashion onto the end of the beam so only one bearing is on the axle. With the axle securely communicable the inside of the bearing, twist the bicycle outward and around as y'all pry the bearing out. Flip the bicycle over and echo.

Tip:Some ready-ups use begetting spacers that sit between the two bearings when in the wheel, while other bearings accept built-in spacers. These are near commonly constitute in longboard wheels and bearings. If your bearings have spacers, be sure to keep rail of them in your hardware tray.

Stride 3. Insert Bearings into New Wheels

Brainstorm by sliding your two bearings shield-side down onto your skateboard'due south truck axle. Press your wheel onto the summit bearing until it is fully seated in the cycle. You may demand to put your weight into it and plow the bicycle until the bearing is evenly seated. Flip the cycle over and repeat to get the second bearing in.

Stride 4. Mountain Wheels

Now that your bearings are in your new wheels y'all can mount them back on the trucks' axles. Slide the wheel on the axle with the correct side facing out. Some wheels take graphics or angled cuts that betoken which side belongs on the outside. But for others, it doesn't matter and you can choose to mount them yet you like. One time that is decided, put the axle nut on by threading it until it is finger-tight. Using a skate tool or wrench, tighten the nut until the wheel has about no wiggle room between the truck and the nut. Over tightening can damage your bearings.

From here, your board is ready to go and you can rip some fresh urethane!

Maintenance

At some point replacing skateboard wheels is necessary, but sometimes you tin can go a little actress life out of your used wheels. Here are some tips for maintaining your wheels.

Rotate Your Wheels

To foreclose your wheels from coning, or wearing out unevenly, you can rotate them to different axles. You lot will want to crisscross the rear wheels to the forepart and crisscross the fronts to the rear. Yous tin practice this every 3 months or whenever you clean or replace your bearings.

Ready Flat Spots

After some employ, harder skateboard wheels volition tend to become flat spots. Flat spots create rough vibrations through your board, putting your smooth ride in jeopardy and slowing you down. To set up this, you can practice powerslides on rough pavement to grind downward the wheel to until it rolls smoothly once again. If you cannot powerslide, you lot can exercise the same action while property your board with your hands.

Clean Your Wheels

Although cleaning your skateboard wheels doesn't exercise much for them, information technology can help to prolong the life of your bearings. Whatever time that you lot have your bearings out of the wheels, accept a newspaper towel and wipe whatsoever gunk out of the middle of them. Bank check out our guide to cleaning bearings for more data.

Keep Learning

Still Have Questions?

Nosotros're hither to help. Y'all can call, e-mail, chat or IM during business hours 7 days a week. Our customer service staff skates…a lot. They know their stuff and are happy to help you with all things skate.

888.450.5060
info@tactics.com

Source: https://www.tactics.com/info/how-to-change-skateboard-wheels